Escon Files & Tools: Umang Marketing - Authorized Distributors for Wikus Germany Bimetal Band Saw Blades, Everising Band Saw & Circular Saw Machines, Escon Files & Tools, Classic Industrial V-Belts, Solar Diamond Tools & Magicut Hole Saws based in Bengaluru, Karnataka State (India)

Escon Files and Tools

Umang Marketing is the authorized distributors for world class Escon Steel Rasp Files, Round Bastard Files, Flat Bastard, Round Files, Round Smooth Files, Steel Machinists Files, Half Round Bastard Steel Files, Cut Slim Taper Saw Files etc.

We also supply Mist Coolants for TCT Circular Saw cutter applications which helps to enhance the cutter life.

Machinist Files

FLAT

FLAT
Size	INCHES	4	6	8	10	12	14
Size	MM	100	150	200	250	300	350
W	MM	12	16	20.5	25.0	29.8	35.5
T	MM	3	4	4.45	5.80	6.1	7.1

HAND

HAND
Size	INCHES	4	6	8	10	12	14
Size	MM	100	150	200	250	300	350
W	MM	12	16	20.5	25.0	29.8	35.5
T	MM	3	4	4.45	5.80	6.1	7.1

HALF ROUND

HALF ROUND
Size	INCHES	4	6	8	10	12	14
Size	MM	100	150	200	250	300	350
W	MM	12	16.1	19.8	24.6	29.55	34.5
T	MM	3	4.7	5.9	7.3	8.60	10.0

ROUND

ROUND
Size	INCHES	4	6	8	10	12	14
Size	MM	100	150	200	250	300	350
T	MM	3.8	6.3	7.15	9.25	12	16

SQUARE

SQUARE
Size	INCHES	4	6	8	10	12	14
Size	MM	100	150	200	250	300	350
T	MM	3.9	6	7.7	9.6	12.2	15.9

THREE SQUARE

THREE SQUARE
Size	INCHES	4	6	8	10	12	14
Size	MM	100	150	200	250	300	350
T	MM	9.0	12.5	15.0	19.0	12.6	24.6

WARDING

WARDING
Size	INCHES	3	3.5	4	6	8
Size	MM	75	90	100	150	200
W	MM	10	9.5	12.1	16.4	20.5
T	MM	1.5	1	1.4	2.3	2.9

KNIFE

KNIFE
Size	INCHES	4	6	8	10
Size	MM	100	150	200	250
W	MM	17.4	22.3	27.4	35.5
T	MM	4.4	5.4	6.6	7.6

Saw Files

SAW FILE

SAW FILES
		HEAVY TAPER	REGULAR TAPER	SLIM TAPER	EXTRA SLIM TAPER	DOUBLE EXTRA TAPER	BAND SAW

Length Inches	Length MM	W	W	W	W	W	W
3	75	8.2	7.2	-	-	-	-
3.5	90	9.0	8.0	-	-	-	-
4	100	10.0	9.0	6.1	5.0	4.5	-
4.5	110	10.5	10.0	7.2	6.1	-	-
5	125	12.5	10.5	7.2	6.1	5.0	10.5
6	150	13.5	12.5	9.0	7.2	6.1	12.7
7	175	15.0	14.5	10.5	9.0	7.2	13.5
8	200	16.0	15.0	12.5	10.5	8.2	15.0
9	225	19.0	16.0	13.5	-	-	-
10	250	21.6	19.0	15.0	-	-	-

SAW FILE

SAW FILES
		MILL REGULAR TSE	MILL BLUNT TRE	MILL BLUNT ORE	MILL BLUNT TSE

Length Inches	Length MM	W x T	W x T	W x T	W x T
4	100	11 x 1.9	-	-	-
6	150	16.0 x 3.0	16.0 x 3.0	16.0 x 3.0	16.0 x 3.0
7	175	18. x 3.2	18. x 3.2	18. x 3.2	18. x 3.2
8	200	20.4 x 3.5	20.4 x 3.5	20.4 x 3.5	20.4 x 3.5
9	225	-	24.0 x 3.8	24.0 x 3.8	24.0 x 3.8
10	250	25.1 x 4.4	25.1 x 4.4	25.1 x 4.4	25.1 x 4.4
12	300	30.3 x 5.3	30.3 x 5.3	30.3 x 5.3	30.3 x 5.3
14	350	36.0 x 6.5	-	-	36.0 x 6.5
9	225	19.0	16.0	13.5	-
10	250	21.6	19.0	15.0	-

PIT SAW

PIT SAW
Size	INCHES	4	4.5	5	6
Size	MM	100	110	125	150
W	MM	8.3	9.3	10.3	11.3
T	MM	4.2	4.7	5.2	5.7

ROUND CHAIN SAW

ROUND CHAIN SAW
Size	INCHES	6	DIA	1/8	9/64	5/32	11/64	-	-	-
Size	MM	150	T	3.2	3.5	4.0	4.5	-	-	-
W	INCHES	8	DIA	3/16	13/64	7/32	15/64	1/4	5/16	3/8
-	MM	200	T	4.8	5.16	5.5	6.0	6.3	8.0	9.6

DOUBLE ENDED SAW

DOUBLE ENDED SAW
Size	INCHES	6	7	8	9	10
Size	MM	150	175	200	225	250
W	MM	6.1	6.1	7.2	9.0	10.0

FEATHER EDGE SAW

FEATHER EDGE SAW
Size	INCHES	5	6
Size	MM	125	150
W	MM	27.3	27.3
T	MM	9.6	9.6

PIT SAW

PIT SAW
Size	INCHES	6	8	10	12
Size	MM	150	200	250	300
W	MM	20.4	25.1	30.3	30.6
T	MM	3.5	4.8	5.6	5.6

File Selection

FILE SELECTION
MACHINIST FILES	FILE TYPE	USES
	FLAT, FLAT SUPER LIGHT	Used in practically all traders for general work on iron, steel etc. for smoothing surfaces and for rapidly removing sharp edges and burr.
	HAND	Have one uncut safe edge and so can be used in corners and close to shoulders.
	HALF ROUND	Used for general purpose and for rapid removal of metal from convex and concave as well as fat surfaces.
	SQUARE	Square files are used principally for fling slots, keyways and also for general surface fling. In larger sizes, the square file is preferred to the flat file, because of the heavier section and four fling surfaces.
	ROUND	Mainly used to file circular openings or concave surfaces.
	3-SQUARE	Used for fling internal acute angles, clearing out square corners, etc.
	PILLER	Suitable for enlarging small slots and keyways or for jobs where the hand file is too wide or too thick to be used.
	WARDING	These are used principally by locksmiths in reparing or fling ward notches in keys. Also suited for use in narrow spaces where other files will not fit.
	KNIFE	Generally used by tool and die maker for slots, keyways and fling narrow passages in cutting slant metal shapes.
SAW FILES
	TAPER, SLIM, EXTRA SLIM, DOUBLE EXTRA, REGULAR, HEAVY	Taper saw files are for sharpening standard hand saws or other saws having 60 degree angle teeth. In general, the extra slim and double extra slim in the short length are for fine teeth saws and the longer lengths of the regular or slim are for coarse teeth saw.
	DOUBLE ENDER	These files have no tang, instead are tapered at both ends. They are used to sharpen saws having a 60 degree angle. The files can be used from both ends and are supplied with handles.
	BAND SAW - BLUNT	Band saw blunt files are for sharpening standard blades having well rounded gullets.
	PIT SAW	Used for sharpening pit saws and also very popular as all purpose files.
	MILL - REGULAR	Mill files are used for sharpening mill saws or circular saws and various cutting tools and as a genral purpose shop file.
	MILL - ORE/TRE	Same as regular mill files except that they have 1 or 2 round edges. The round edges prevent the files from causing sharp corners or edges in the gullets of circular cross cut saws.
	FARMERS OWN	A handy file for farmers. Used for sharpening agricultural tools and knives of reaping and moving machines.
	DOUBLE EDGE	Used for fling saws where included angle of teeth is less than 60 degree.
	FEATHER EDGE	Used for fling saws where included angle of teeth is less than 60 degree.

Classic Industrial V-Belts

Umang Marketing is the authorized distributors for top quality Classic Industrial V-Belts, designed specially for reverse-bend drive by positioning tensile members closer to the bottom compare to that of conventional multiple V-belts A, B, & C.

Particularly suitable to Agricultural & Industrial Machinery, where V belts are often driven with tension idler pulley on their back. Heat, Oil and Anti-Static resistant.

1. Escon V-Belts

Cover: The cut cover fabric is impregnated with special NEOPRENE rubber compound to provide strong abrasion resistance on the pulley groove and to protect the inner part of the belts.
Tension Member: Specially treated tough polyester cords impart high strength, low elongation and excellent resistance to bending fatigue.
Top Compression Section: High heat dissipating rubber compound with-stands increased flexong and sudden shock loads.
Insulation Section: This holds the tension members in place and acts as binding force between cords, top and bottom compression sections.
Bottom Compression Section: This is specially compounded to resist compression fatigue and heat for longer service life.

ESCON V-BELT SPECIFICATIONS
Belt Section	Nominal Top Width	Nominal Thickness	Nominal Angle	Belt Length Range Inside Length		Minimum Recommended Pulley Pitch Dia	IS : 2494 Specifications		ESCON Results
	(mm)	(mm)	(°)	(Inch)	(mm)	(mm)	Minimum Tensile Strength (Kgs)	Minimum Elongation at Break (%)	Tensile Strength (Kgs)	Elongation at Break (%)
A	13.0	8.0	40	16-180	406-4572	80	300	15.0	370	11.0
B	17.0	11.0	40	20-400	508-10160	125	425	15.0	550	11.0
C	22.0	14.0	40	36-600	914-15240	200	800	15.0	1050	11.0
D	32.0	19.0	40	88-600	2225-15240	355	@460 Kg Load	5.0	@460 Kg Load	3.0
E	38.0	23.0	40	158-600	4013-15240	500	@612 Kg Load	5.0	@612 Kg Load	3.0

2. Escon Wedge Belts

Escon Wedge Belts contain high modules polyester cords, which together with specially formulated bottom compression rubber compound and insulation rubber, constitute over unshakeable union even under severest flexing conditions. The cords retain their designed and correct position under tension without any cord movement. Escon Wedge Belts do not buckle even on toughest drives.

Escon Wedge Belts are capable of transmitting more than twice as much power as traditional Vee belts, hence resulting in space saving, narrower pulleys, reduced overhung and increased bearing life.

ESCON WEDGE BELT SPECIFICATIONS
Belt Section	Nominal Top Width (mm)	Nominal Thickness (mm)	Nominal Angle (°)	Belt Length Range Pitch Length (mm)	Minimum Recommended Pulley Pitch Dia (mm)
SPZ	10.0	8.0	40	630-3550	63
SPA	13.0	10.5	40	800-4500	90
SPB	17.0	13.5	40	1259-10000	160
SPC	22.0	18.0	40	2000-12500	224

3. Escon Raw Edge Cogged Belts

Belt Construction

1. Top Fabric: Resists wear, oil and heat with excellent flexibility
2. Tension Member: Specially treated low stretch and high strength polyester cable cords that provide great resistance to bending fatigue and stability of belt length.
3. Compression Rubber: Specially compounded rubber with fibers that keeps stability of the normal cross section of the belt on the pulleys, providing longer service life.
4. Bottom Fabric: Resists oil and heat with excellent flexibility and provides great resistance to cracking of the compression rubber.

ESCON RAW EDGE COGGED BELT SPECIFICATIONS (All Dimensions in MM)
Cross Section	Nominal Top Width (mm)	Nominal Thickness (mm)	Angle (°)
AX	13.0	8.0	36
BX	17.0	11.0	36
CX	22.0	14.0	36
10 MM	10.0	8.0	34/36

4. Escon Conveyor Belting

1. Belt Width: The Escon Conveyor Belts are available in standard width from 150 mm to 2000 mm in open and endless length as per customer's requirement.
Construction: Conveyor belt generally consists of cover rubber, carcass and rubber skim coat.
Cover Rubber: Covers of natural or synthetic rubber are designed to protect the carcass from abrasion, impact, deterioration and other injuries influences. They are compounded to meet particular service conditions such as abrsion, oil, heat, fire, chemical, resistant and antistatic etc.
Carcass: Carcass of belt maintains the belt tension and supplies structural strength, in supporting and pulling the load. Carcass consists of multiple plies of rubber impregnated fabric bonded with friction and skim coats. The fabrics most commonly used are nylon, polyester and cotton etc.
Rubber Skim Coat: An extra layer compound between plies that increases flex and creates a more elastic link so that plies flex without separation. Skim coated cushion fabric helps in protecting against moisture.
Cover Selection: Escon Conveyor Belts are manufactured with the following cover grades to meet requirement of specific applications.

Classification: • Heat Resistant Conveyor Belt • Oil Resistant Coveyor Belt • Fire Resistant Conveyor Belt • Food Conveyor Belt • Anti-Static Conveyor Belt • Abrassion Resistant Conveyor Belt • Color Conveyor Belt • Cold Resistant Conveyor Belt • Chemical Resistant Conveyor Belt

ESCON RAW CONVEYOR BELTING SPECIFICATIONS
BELT TYPE	GENERAL APPLICATION
M-24	Suitable for rugged services as crushed metallic ores, limestone, granite etc.
N-17	Suitable for moderately abrasives like Asbestos, Ash Bauxite Cement, Lime etc.
HR T1	Suitable for transporting hot material (upto 125°C for coarse material and 100° for fines)
HR T2	Suitable for transporting hot material (upto 150°C for coarse material and 125° for fines)
SHR T3	Suitable for transporting hot material above 150°C and up to 200°
Oil Resistant (OR)	Compounded to give very high resistance to minerals & vegitable oil etc.
Food Conveyor (Hygienic)	Suitable for handling confectionary, food, pharmaceuticals etc.
Fire Resistant (FR)	Recommended for use in coal & such types of mines where ambient temparature may not be high but there is distinct hazard of belts being enveloped in fire.